Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
facilities:fablab:inductions:lasercutter:start [2019/12/04 15:32]
Michael Byrne
facilities:fablab:inductions:lasercutter:start [2019/12/04 16:55]
Michael Byrne
Line 606: Line 606:
  
 ===== New Laser induction Activity Dec 2019- usb stick ===== ===== New Laser induction Activity Dec 2019- usb stick =====
-<WRAP hideslide>Hide from slideshow +<WRAP hideslide> 
-{{:facilities:fablab:inductions:lasercutter:usbsticks.jpg?direct&200|}}+ 
 +{{:facilities:fablab:inductions:lasercutter:usbsticks.jpg?direct&400|}} 
 ====Background==== ====Background====
 After using the Chair design for several year it became aparent that we needed a new practical take home activity that contained some intrinsic value. Why not make a customised usb stick. The small cost of the usb stick would be outweighed by the utility of the outcome.    After using the Chair design for several year it became aparent that we needed a new practical take home activity that contained some intrinsic value. Why not make a customised usb stick. The small cost of the usb stick would be outweighed by the utility of the outcome.   
 ====Process====  ====Process==== 
-the insides+the insides of usb were measured up with vernier Callipers and drawn up to create a template for the naked USB Board to be retained inside.  
 +{{ :facilities:fablab:inductions:lasercutter:naked_usb_template.pdf |Naked Usb Template}} 
 + 
 +In Illustrator, Corel Draw, Inkscape (or my case Affinity Design) this template can be combined with artwork to create a Usb Stick design that is cut out on the laser and then assembled into a sandwich of 2 or three layers around the naked usb board. 11 of these designs have been prepare for Participants to select, prepare in corel draw for cutting as a practical exercise in their laser induction.  
 + 
 + 
 +====Design Considerations==== 
 +  * usb connector needs to not be obstructed  
 +  * its preferable that the usb stick obstruct the //port next door// 
 +  * its preferable to us offcuts for the laser materials  
 +  * its preferable to try a couple of different techniques in the session so that participants get to see a range of techniques and use cases for the Laser and broader FL resources  
 +  * its a requirement for the timely completion of the induction that the design require a minimum of cutting and especially etching time.  
 +  * its a requirement for the timely completion of the induction that artwork is straight forward to lay out  
 +  * There is no tome in the 2hour induction for participants to make their own original design but are welcome to book and use the laser in the future.      
 + 
 + 
 +===Preprepared Artwork===    
 +{{ :facilities:fablab:inductions:lasercutter:chingy_usb_.pdf |Chingy}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:batman_usb.pdf |Batman}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:cactususb.pdf |Cactus}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:dashund_usb.pdf |Dachshund}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:donut_usb_.pdf |Donut}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:elephantusb.pdf |Elephant}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:hotdog_usb_.pdf |Hotdog}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:kenny_stick.pdf |Kenny}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:mjölnirusb.pdf |Mjölnir}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:rocketusb.pdf |Rocket}} 
 + 
 +{{ :facilities:fablab:inductions:lasercutter:strawberry_usb.pdf |}}
  
 +{{ :facilities:fablab:inductions:lasercutter:frogusb.pdf |Frog}}
 </WRAP> </WRAP>
  
  

We acknowledge Aboriginal and Torres Strait Islander peoples and their continuing connection to land and as custodians of stories for millennia. We are inspired by this tradition in our work to share and preserve Queensland's memory for future generations.